Technical memo Machine elements ~8 min read
Ball and roller bearings

Bearing life calculation: L10 formula, life in hours and reliability (ISO 281)

Published November 19, 2026 — the L10 basic rating life formula, its conversion to hours, the equivalent dynamic load, variable loads, the reliability factor a1, worked examples, formulas to copy into Excel and a free calculator.

(C/P)³ L10 of a ball bearing, in millions of revolutions
(C/P)10/3 L10 of a roller bearing
10⁶/60n From revolutions to hours (n in rpm)

In short: the basic rating life of a bearing is L10 = (C/P)p million revolutions, where C is the basic dynamic load rating (manufacturer's catalogue), P the equivalent dynamic load and p = 3 for ball bearings, 10/3 for roller bearings. In hours: L10h = 10⁶ × L10 / (60 × n), n in rpm. Example: ball bearing, C = 14,000 N, P = 2,000 N, 1,500 rpm → L10 = 343 million revolutions, i.e. 3,811 h. L10 is reached by 90 % of bearings; for 99 %, multiply by a1 = 0.25.

1. Bearing life formulas

A bearing rotating under load eventually spalls: the balls or rollers and the raceways go through millions of stress cycles until the metal fatigues. ISO 281 gives the basic rating life, written L10: the number of revolutions that 90 % of a large group of identical bearings reach or exceed before the first spall.

QuantityFormulaUnit
Basic rating life L10(C / P)pmillion revolutions
Exponent p3 for ball bearings; 10/3 for roller bearings—
Life in hours L10h106 × L10 / (60 × n)hours (n in rpm)
Required basic dynamic load ratingP × (60 × n × Lh / 106)1/psame unit as P
Modified rating life Lnma1 × aISO × L10million revolutions

C, the basic dynamic load rating, is the constant load under which the bearing reaches L10 = 1 million revolutions. It is listed in the manufacturer's catalogue for each bearing. P and C must be in the same unit (N, kN or lbf): only their ratio matters. The high exponent makes the calculation very sensitive to load: life varies as the cube of C/P.

100 %100 %51 %48 %30 %26 %12.5 %9.9 %load P1.25 × P1.5 × P2 × PBall bearing (p = 3)Roller bearing (p = 10/3)
L10 life as a % of the life under load P. A 25 % higher load divides the life by 1.95 (ball bearings); doubling the load divides it by 8 (ball) or 10 (roller).

2. Bearing life calculator

Enter the basic dynamic load rating C from the catalogue, the radial load Fr and axial load Fa and the factors X and Y (leave X = 1 and Y = 0 for a purely radial load), the speed and the required reliability. The target life is optional: it gives the load rating C you would need.

Equivalent load P
—
L10 life (million revolutions)
—
L10h life
—
Life at the chosen reliability
—
C required for the target life
—

Default values: the ball bearing example from section 5. The X and Y factors depend on the bearing type and the Fa/Fr ratio: use the manufacturer's catalogue values. The calculation ignores aISO (lubrication, contamination), taken as 1.

3. The equivalent dynamic load P

C is defined for a purely radial load (purely axial for a thrust bearing). When the bearing carries both a radial load Fr and an axial load Fa, they are replaced by a notional radial load giving the same life: P = X·Fr + Y·Fa. Under a purely radial load, P = Fr.

FrFaP = X·Fr + Y·FaOuter ringBall (rolling element)Inner ringRotating shaftequivalent dynamic loadC: load givingL10 = 1 million revolutions
The radial load Fr and the axial load Fa are combined into a single equivalent radial load P, to be compared with the bearing's basic dynamic load rating C.

The X and Y factors are not universal: they depend on the bearing type (deep groove ball, angular contact, tapered roller…), the contact angle and, for deep groove ball bearings, the Fa/C0 ratio. As long as Fa/Fr stays below a limit value e given by the manufacturer, the axial load has no effect and P = Fr. Above it, take X and Y from the catalogue.

Variable load and speed

If the load changes during the duty cycle, a mean equivalent load is calculated, weighted by the share of revolutions Ui spent under each load Pi: Pm = (Σ Ui · Pip)1/p, with Σ Ui = 1. If the speed changes too, Ui is the share of ni × ti in the total, and the mean speed is Σ ni × ti / Σ ti.

Example, ball bearing: 20 % of revolutions under 3,000 N, 50 % under 2,000 N and 30 % under 1,000 N. Pm = (0.2 × 3,000³ + 0.5 × 2,000³ + 0.3 × 1,000³)1/3 = 2,133 N, much closer to the high load than the plain average (1,900 N): high loads count cubed.

4. Reliability: the a1 and aISO factors

L10 accepts that 10 % of bearings fail before the calculated life. When a failure is costly, a higher reliability is targeted and the life is reduced with the factor a1. Values from ISO 281:2007:

ReliabilityLifea1Example: 3,811 h at 90 %
90 %L10m13,811 h
95 %L5m0.642,439 h
96 %L4m0.552,096 h
97 %L3m0.471,791 h
98 %L2m0.371,410 h
99 %L1m0.25953 h

These values are the rounded result of a1 = 0.95 × (ln(100/R) / ln(100/90))2/3 + 0.05, R being the reliability in %, a Weibull law with a minimum life. Earlier editions of the standard (before 2007), without that minimum term, gave slightly lower values (0.62 at 95 %, 0.21 at 99 %): some software and older catalogues still use them.

The aISO factor adjusts the life for actual conditions: lubricant viscosity at operating temperature, cleanliness (particle contamination), and the bearing's fatigue load limit Pu. It can exceed 1 with excellent lubrication and cleanliness, and drop well below with a too-thin oil or a contaminated environment. It is calculated with the ISO 281 charts or the manufacturer's online tool; this memo does not quantify it.

5. Worked examples

The basic dynamic load ratings below are example values: for a real bearing, read C in the catalogue of the chosen part.

CaseCalculationResult
Ball, C = 14,000 N, P = 2,000 N, 1,500 rpm(14,000 / 2,000)³ = 343; 343 × 10⁶ / (60 × 1,500)343 million rev; 3,811 h
Same at 99 % reliability0.25 × 3,811953 h
Same under twice the load (P = 4,000 N)(14,000 / 4,000)³ = 42.942.9 million rev; 476 h
Roller, C = 50,000 N, P = 5,000 N, 1,000 rpm1010/3 = 2,154; 2,154 × 10⁶ / (60 × 1,000)2,154 million rev; 35,907 h
Required C: 20,000 h at 1,500 rpm, ball, P = 2,000 NL10 = 60 × 1,500 × 20,000 / 10⁶ = 1,800; 2,000 × 1,8001/3C ≥ 24,329 N
Same at 99 % reliability2,000 × (1,800 / 0.25)1/3C ≥ 38,620 N

For a wheel, life is counted in distance: L10 in millions of kilometres = π × D × L10 / 1,000, with D the wheel diameter in metres. A 0.6 m wheel whose bearing makes 343 million revolutions thus covers 0.647 million km.

6. Bearing life in Excel: formulas to copy

With the exponent p in A2 (3 or 10/3), C in B2, P in C2, the speed n in D2 (rpm), the reliability R in E2 (in %, from 90 to 99.9) and the target life in F2 (h), the ball bearing example gives:

ResultExcel formulaExample value
L10 (million rev), in G2=(B2/C2)^A2343
L10h (hours), in H2=G2*10^6/(60*D2)3,811.1
a1 factor for R, in I2=0.95*(LN(100/E2)/LN(100/90))^(2/3)+0.050.2483 (R = 99)
Life at reliability R (hours)=I2*H2946.4
C required for F2 hours=C2*(60*D2*F2/10^6/I2)^(1/A2)38,706 (F2 = 20,000)

The a1 formula gives the exact value (0.2483) where the table rounds to 0.25, hence 946 h instead of 953. Enter 10/3 in A2 as =10/3. The same formulas work with C and P in lbf.

7. What the calculation does not tell

  • A statistical life: L10 describes a population, not one bearing. A given bearing can fail earlier or last much longer.
  • Fatigue only: the calculation assumes a correctly mounted, well lubricated, clean bearing. Wear from contamination, poor lubrication, misalignment or forced mounting shorten the life without the formula seeing it.
  • Static load: when stationary, slowly oscillating or under shock, the bearing is also checked with its basic static load rating C0 and the static safety factor s0 = C0 / P0, following the manufacturer's recommendations.
  • Speed limit and temperature: each bearing has a reference speed and a limiting speed in the catalogue; heat degrades the lubricant, and so aISO.
  • Fits: the shaft and housing tolerance depends on whether the load rotates or is stationary; see the ISO 286 fits memo and the manufacturer's recommendations.

Printable version: the formula sheet as a PDF (A4, no sign-up): formulas, reliability factors, examples and Excel formulas.

8. FAQ

What is the L10 life of a bearing?

It is the basic rating life defined by ISO 281: the number of revolutions (in millions) that 90 % of a large group of identical bearings, running under the same conditions, reach or exceed before the first sign of fatigue. 10 % of the bearings in the group may therefore fail before L10.

How do you calculate bearing life in hours?

First calculate L10 = (C/P)^p in million revolutions, with p = 3 for a ball bearing and p = 10/3 for a roller bearing, then L10h = 10^6 × L10 / (60 × n), n being the speed in rpm. Example: C = 14,000 N, P = 2,000 N, ball bearing, 1,500 rpm: L10 = 343 million revolutions, i.e. 3,811 hours.

What is the difference between C and C0?

C is the basic dynamic load rating: the constant load under which the bearing reaches an L10 life of one million revolutions. It is used for the life calculation of a rotating bearing. C0 is the basic static load rating: it is used to check a stationary, slowly oscillating or shock-loaded bearing against permanent deformation of the raceways.

What happens to bearing life if the load doubles?

It is divided by 2³ = 8 for a ball bearing and by 2^(10/3), about 10, for a roller bearing. Conversely, reducing the load by 20 % multiplies a ball bearing's life by 1.95. That is why an underestimated load distorts the result so much.

How do you calculate bearing life for 99 % reliability?

Multiply L10 by the ISO 281 reliability factor a1: 0.64 for 95 %, 0.55 for 96 %, 0.47 for 97 %, 0.37 for 98 % and 0.25 for 99 %. The L1 life, reached by 99 % of bearings, is therefore a quarter of L10: 953 hours instead of 3,811 in the example.

Read next