Technical memo Machine elements ~7 min read
Belt drives

Belt length calculator: formula, center distance and wrap angle for two pulleys

Published November 21, 2026 — the length of an open or crossed belt on two pulleys, exact and approximate formulas, the center distance for a stock belt, the wrap angle, the speed ratio, timing and V-belts, Excel formulas and a free calculator.

2C + π(D+d)/2 + (D − d)²/4C: the length, to a few hundredths
180° − 2φ Wrap angle on the small pulley
z·p/π Pitch diameter of a timing pulley

In short: an open belt on two pulleys of diameters D and d, at center distance C, has a length of L ≈ 2·C + π·(D + d)/2 + (D − d)²/(4·C). The exact formula replaces the last term with the tangent geometry: L = 2·C·cos φ + π·(D + d)/2 + φ·(D − d), with sin φ = (D − d)/(2·C). Example: D = 200, d = 100, C = 500 mm → L = 1,476.2 mm, a 168.5° wrap angle on the small pulley. For a stock belt of length L, the center distance is C = (b + √(b² − 8·(D − d)²))/8 with b = 2·L − π·(D + d).

1. Belt length formulas

DdCφθ= 180° − 2φsmall pulleylarge pulley
Both spans are tangent to the pulleys and inclined at φ, with sin φ = (D − d)/(2·C). The belt wraps the small pulley over θ = 180° − 2φ and the large one over 180° + 2φ.
QuantityFormula
Span angle φsin φ = (D − d) / (2·C)
Exact length, open beltL = 2·C·cos φ + π·(D + d)/2 + φ·(D − d)
Approximate length, open beltL ≈ 2·C + π·(D + d)/2 + (D − d)² / (4·C)
Center distance for a length LC = (b + √(b² − 8·(D − d)²)) / 8, with b = 2·L − π·(D + d)
Wrap anglesmall pulley 180° − 2φ; large pulley 180° + 2φ
Speed ratio (no slip)i = n1 / n2 = D / d
Belt speedv (m/s) = π · d (mm) · n (rpm) / 60,000

φ is in radians in the exact formula. The approximate formula replaces cos φ and φ with their series expansions; the difference stays within a few hundredths of a millimetre as long as the pulleys are of similar size and the center distance is large compared with their difference (0.004 mm in the example below). With a high ratio and a short center distance it grows: for D = 400, d = 80 and C = 300 mm, 1,441.5 mm exact versus 1,439.3 mm approximate. D and d are the diameters the belt's neutral line runs on (see section 5).

2. Belt length calculator

Enter both diameters and the center distance, in the same unit. Optional: the speed of the driving (small) pulley, the pitch of a timing belt for the number of teeth, and the length of a stock belt for the matching center distance.

Exact length
—
Approximate length
—
Wrap small / large pulley
—
Ratio, driven speed, belt speed
—
Number of teeth
—
Center distance for the stock belt
—

The center distance for a stock belt is solved with the exact formula, by successive approximation, for both open and crossed belts. Default values: the example from section 3. For a timing belt, enter the pitch diameters z·p/π.

3. Worked examples

CaseCalculationResult
Open, D = 200, d = 100, C = 500 mmφ = asin(100/1,000) = 0.1002 radL = 1,476.24 mm (approximate: 1,476.24)
Wrap angle180° − 2 × 5.74°168.5° (small); 191.5° (large)
Speeds, motor at 1,450 rpm on dn₂ = 1,450 × 100/200; v = π × 0.1 × 1,450/60725 rpm; 7.59 m/s
Stock belt of 1,500 mmb = 3,000 − π × 300 = 2,057.5C = 511.94 mm
Crossed, same pulleys, C = 500 mmφ = asin(300/1,000) = 0.3047 radL = 1,516.59 mm; wrap 214.9°
GT2 timing belt (2 mm pitch), 20 and 40 teeth, C ≈ 100 mmPitch Ø 12.73 and 25.46; L = 260.4 mm = 130.2 teeth130-tooth belt: C = 99.80 mm

For the 1,500 mm belt, the inverse formula from section 1 gives 511.94 mm and the exact formula 511.94 mm too (0.002 mm apart). Tension is in any case set by moving one pulley: allow an adjustment range on both sides of the calculated center distance, following the belt manufacturer's recommendations.

4. Open or crossed belt

A crossed belt reverses the driven pulley's direction of rotation and wraps both pulleys more. Its spans rub where they cross: it is kept for flat or round belts at low speeds. Its length follows the inner tangents:

  • exact: L = 2·C·cos φ + (π + 2·φ)·(D + d)/2, with sin φ = (D + d)/(2·C);
  • approximate: L ≈ 2·C + π·(D + d)/2 + (D + d)²/(4·C);
  • wrap: 180° + 2·φ on each pulley.
Open beltsame direction of rotationCrossed beltreversed direction of rotation
An open belt keeps the direction of rotation; a crossed belt reverses it and wraps each pulley over 180° + 2φ, at the cost of the spans rubbing where they cross.

5. Timing, V- and flat belts: which diameter to use

The formulas apply to every belt type, provided you use the diameter the belt's neutral line runs on, the line that does not stretch in bending:

BeltDiameter to useResulting length
Timing (synchronous)Pitch diameter z·p/π (z teeth, pitch p)Pitch length = pitch × number of belt teeth
V-beltDatum (pitch) diameter of the groove, given by the pulley manufacturerDatum (pitch) length; the inside length is shorter, by an amount that depends on the section
FlatPulley diameter + belt thicknessMid-thickness length

Common timing belt pitches: 2 mm (GT2), 3, 5, 8 and 14 mm (HTD 3M to 14M profiles), 5.08 mm (XL, 1/5 inch) and 9.525 mm (L, 3/8 inch). A timing belt only exists in whole numbers of teeth: calculate the length for the center distance you want, divide by the pitch, pick the closest belt in the catalogue, then recalculate the center distance with the calculator. For a V-belt, do the same with the catalogue's datum lengths, checking which length (inside or datum) it lists.

The torque the belt transmits arrives on a shaft that must carry it: see the shaft torsion calculation, and bearing life for the radial load caused by belt tension.

6. Belt length in Excel

With D in A2, d in B2, the center distance C in C2 and a stock belt length in D2 (example values: 200, 100, 500, 1,500):

ResultExcel or LibreOfficeValue
Exact length=2*C2*COS(ASIN((A2-B2)/(2*C2)))+PI()*(A2+B2)/2+ASIN((A2-B2)/(2*C2))*(A2-B2)1,476.243
Approximate length=2*C2+PI()*(A2+B2)/2+(A2-B2)^2/(4*C2)1,476.239
Small pulley wrap (°)=180-2*DEGREES(ASIN((A2-B2)/(2*C2)))168.52
Center distance for length D2=(2*D2-PI()*(A2+B2)+SQRT((2*D2-PI()*(A2+B2))^2-8*(A2-B2)^2))/8511.94

These formulas were checked in LibreOffice Calc on the example (values identical to the table in section 3).

Printable version: the formula sheet as a PDF (A4, no sign-up): formulas, examples and Excel formulas.

7. FAQ

How do you calculate belt length?

For an open belt on two pulleys of diameters D and d at center distance C: L ≈ 2·C + π·(D + d)/2 + (D − d)²/(4·C). The exact formula is L = 2·C·cos φ + π·(D + d)/2 + φ·(D − d), with sin φ = (D − d)/(2·C). For D = 200, d = 100 and C = 500 mm, L = 1,476.2 mm.

How do you calculate center distance from belt length?

With b = 2·L − π·(D + d), the center distance is C = (b + √(b² − 8·(D − d)²))/8. It is the exact solution of the approximate length formula. For a 1,500 mm belt on 200 and 100 mm pulleys, C = 511.9 mm.

Which pulley diameter should be used in the calculation?

The diameter the belt's neutral line runs on: the datum (pitch) diameter for a V-belt, the pitch diameter z·p/π for a timing belt, and the pulley diameter plus the belt thickness for a flat belt.

How do you calculate timing belt length?

Calculate the pulleys' pitch diameters, z·p/π, then the pitch length with the exact formula. Divide by the pitch to get the number of teeth, round to the tooth count of an existing belt, and recalculate the center distance for that length. A 130-tooth GT2 belt (260 mm) on 20- and 40-tooth pulleys gives a center distance of 99.8 mm.

What is the wrap angle on the small pulley?

For an open belt, θ = 180° − 2·φ, with sin φ = (D − d)/(2·C). It decreases as the diameter difference grows or the center distance shrinks. For D = 200, d = 100 and C = 500 mm, θ = 168.5°. The large pulley is wrapped over 180° + 2·φ.

Read next